Відео

That cat tho... 😂😂❤❤

Dude thank you so much you have no idea how much you just helped me! You're the man!!

So far I've looked at 3 different videos on this problem and each show a different cause of the problem. Going to add this to the list of things to check, thanks

Bless The internet and bless you❤

Do you also teach sealed system?

This video was a life saver for me. Fixed my dryer all by myself. Thank you!

Thank you, big help ❤

Omg dam bro you save me a lot of money thank you

Replace the board and the power came back on then I put it to wash and the new board went bad again

THa nks you. Can you adjust the water level switch while the machine is turned off, or must the adjustment be made while it is running?

your website you mentioned has a virus attached to it now, you must have sold it to someone who's scamming on it now ;(

👍👍

Wondering if I could get more help.

Thank you

I've got a Samsung front load washer that's setting a 4E code that I cannot figure out. Do you know where I can find the pressure switch voltage or what the ohm readings are supposed to be? All the screens are clean and valves seem to allow water in.

Thank you so much for demonstrating such a wonderful means of moving a washer or dryer! I was trying to move the machine by putting a shovel under the front edge and trying to lever the washer into place. Got to move it about 2" doing that. Using your method I had the job done in a couple of minutes. THANK YOU --- Doctor Dan

Thanks bro I accidently bent it and my mom yelled at me this fixed it your a life saver

Thanks for being a lifesaver. I didn’t know what I was doing wrong. You are awesome!!

Thank you so much that exact same thing happened I fixed it and now it doesn't make that noise that was so helpful I rather try to fix myself then have someone try to rip me off of something that wouldn't be the problem

Modern washing machines don't last long enough for this to be a problem 🤣

Hello I have someone selling a LG direct drive washing machine on Facebook for $40 only 4yrs old, but now has no power due to power surge. Any chance I could get this working cheap?

I notice that when i replaced the pump, the new pump last only 5 months

Keep getting Fd error code

Nice video, good clear images and instructions. My pump has had a small leak for some time and I want to replace it but I cannot separate the pump from the drive shaft. Is there a special trick? Usually my go-to solution for corroded parts is lots of WD40, a tap with a hammer, more WD40, more time. Is that appropriate for this? Thanks. I wanted to add, when you get the washer torn down this far, this is a good opportunity to scrub the plastic drum and remove the accumulation of lint between the that and the perforated metal drum. a few clips removes the cover giving access to the lint in the gap. I used a skinny 24" vent brush. I did this years ago to cure an odor in the clothes. Worked like a charm.

Thanks!

I also found out that powder detergent is bad for the drain because it clumps where the fluid waste to circulate and once the substance builds up will cause it to clogged.

Thank you for sharing this. A big help to me. Great job filming as you’re working 👍

God dont ever call a "tech" to fix a dryer. For one, you can go buy a whole new dryer for a tad more than what he said it would cost for him to fix this issue. And more importantly, this is so so simple to fix yourself and requires zero experience. Literally anyone who can spin a screw driver can fix this in 30 minutes. Dryers are so simple to take apart and so simply designed

I replaced the computer the control panel I just replaced the noise filter still no power can you help

Thanks for posting this, saved me some serious time

Thanks for this, has confirmed my pump is ok.

😂😂😂 so u got a free machine lmao

Good stuff. My water pressure switch I think is not working.

Thanks so much, it worked perfectly for me.

I ran into this once when I was scrapping out an old washer... never thought anything like that could happen....

Dude you are our hero!! Thank you!!!

Bless

I have the same dryer and my sensing light comes on when I try to start my dryer but it will not start. Any suggestions?

Thanks for the upload. Planning the clean out. I own two Newfoundland dogs. We do a bunch of towels Lots of hair and lint. 🙏🏻

Thanks for this. I used some offcuts of craft felt, and it worked really well. Almost like the machines were on casters!

i’m a simple man, i see a girl in a thumbnail and i unsubscribe 😜

Mine does not power on at all no lights no nothing, checked circuit breaker and all is good. What’s the most probable cause???

I was pulling for you (even straining). I love it when you are recording and it finally works. But, then you did say: "I always win!" :)

Do you mean "Correct way to maintain your Whirlpool ...... ?

This is definitely NOT quick job !!!

My whirlpool duet dryer has 240 volts coming in to the unit but wont power on at all.. what should I check to troubleshoot the issue

IN NEED OF A RUBBER TOP STABILZER FOR MOD.gtwn2800d1ww

The screws are on the opposite side that holds it for the big metal vent you cleaned at the end of the video. How do you remove that?

what does E2 mean?